Setup Loadmaster Problems - followup

A few other problems that I did not talk about on my last post. These are all to do with the shell feeder.

I setup the shell feeder, tubes, sliders etc and it was working great. I created approx 100 rounds without any problems. After the first 100 the press started to get very stiff on the down stroke, I noticed that the slide would stick at the top and then slowly creep down before it would act normally again.

I didn’t notice the slider at first, and only really noticed it when I found that the slider rod was warm. In fact it was a little more than just warm, it was positively hot. I didn’t know what to do about this, so tried adding some lube, which helped for a while but did not solve it and caused the case feeder not to feed cases enough. In the end I found that the rod was bent out, so all I needed to do was bend it back in toward the press.

Second problem was caused by the first and it was that the case feeder wasn’t feeding cases into the press again after the problem above. I followed Lee’s instruction and tightened up the screws on the slider. I have over tightened these screws now and they have stripped the plastic out of the slider. I will add some thread lock to these screws so they have something to bit against.

So far I have made approx 400 rounds, I have fired approx 50 and they were all great. Very soft recoil and have not altered my point of aim at all. I have a 2 day IPSC competition this weekend, which is why I have made some many rounds. This will be the first competition that I will be using my own rounds for and I am confident it will help me place better.

I will follow up my posts with some positives I have found with the press, as so far all I have posted is problems and that’s not really representative of my experiences with this press so far. Once setup it was very, very easy to create completed rounds, and of the ones I fired they have all been consistent.

Setup Loadmaster Problems

A few things I was annoyed about before starting. My press only came with the 3 die set. I did not get the universal decapper die either. I’m not sure if this was because of my dealer, or if it’s normal with the Loadmaster. My Loadmaster didn’t come with the shell tray either that goes on top of the case feeder, again no idea if this was a cock up from my dealer or if it’s normal with Lee.
As expected I had a few problems during the set up of the loadmaster, luckily there are some very good setup guides and help available on the web.

The main places I went to get help where:

http://loadmastervideos.com/

http://www.youtube.com/
http://leeprecision.com/xcart/Load-Master-Help.html
 
The first problem I had was that the system was not indexing, I found the problem was that the indexing rod was not engaging the frame. I found a video on Lee’s site that helped me with this problem. Basically I needed to undo the bolt at the base of the unit, twist the press until the indexing rod did engage the frame, and retighten the bolt. It was a nice quick fix, but a little annoying with a brand new press.

Next problem was with the priming system. I was having a lot of problems with the primer not seating correctly, i.e. at funny angles. I solved this by buying the 4 die set along with a universal decapper die. This helped because I resize the brass at the same time as adding a primer, it holds the brass straight and increases the changes of getting a good primer seated.

Next problem with the primers I had was that the slider got bent and the plastic deformed. In the set it includes a second slider, but it’s happened with that one too. I bent the plastic back and it’s working for now, but I do need a new slider. Added to the fact that I’m still getting a few primer placement problems I’m thinking of getting a hand primer tool and do the priming outside the press.

Next problem I had was with the bullet feeder. It was too small for a 9mm bullet to feed from it. The diameter was fine but the bullets are slightly too tall. I took a dremal tool and cut a channel in the top of the feed, it only took a minute but again it’s very annoying that the kit doesn’t work out of the box.

Last thing is the wooden handle of the press keeps coming off in my hand when I apply pressure at the bottom of the action. I haven’t done anything about this yet but am planning to glue the wooden handle back on the press. I believe that this is a common problem with the Lee’s.

Lee Loadmaster arrived

Finally here, Will be picking up my Lee Loadmaster in 9mm tonight.

Will start putting everything together, will take pictures at every step and update this site.

Nothing new

Nothing new, just waiting but still finding time to learn more about reloading.

On line forums are great, you can ask all sorts of silly questions, most of teh time you get the answers you were looking for too. It's stilll always best to be around someone who has reloaded before, hands on experience always comes top.

Hoping that my waiting is nearly over, I'm looking forward to starting reloading.